6ES7 193-0CA10-0XA0
Siemens 6ES7 193-0CA10-0XA0 – ET 200B TB1/DC Terminal Block
Siemens 6ES7 193-0CA10-0XA0 is the TB1/DC terminal block for ET 200B within the SIMATIC ET 200 family. Designed for 24 V DC electronics blocks, it has a 16-channel, three-tier screw-terminal arrangement and a 160 mm width.
Identify the terminal base together with the electronics block fitted to it. The channel count alone does not establish whether the assembly provides inputs, outputs or a combination. Selecting the correct ET 200 terminal block requires checking the electronics reference, wiring diagram and existing cabinet arrangement.
Compatible electronics blocks
ET 200B-16DI / 6ES7131-0BH00-0XB0: 16 digital inputs.
ET 200B-16DO / 6ES7132-0BH01-0XB0: 16 digital outputs.
ET 200B-8DI/8DO / 6ES7133-0BH01-0XB0: 8 inputs and 8 outputs. ET 200B-8DI/8DO HWA / 6ES7133-0BH10-0XB0: the version with hardware output disable.
ET 200B-8RO / 6ES7132-0GF00-0XB0: 8 relay outputs, with a specified switching voltage of 24–60 V DC.
ET 200B-16DO and ET 200B-16DO/2A require different base selections. The all-channel 2 A version, 6ES7132-0BH11-0XB0, uses the TB2 group. Keep the “/2A” designation and the complete order number when identifying a replacement.
Three-tier terminal arrangement
With the 16DI electronics block, terminals 1–16 are inputs, 17–32 provide sensor +24 V, and 33–48 provide sensor M. Do not transfer this assignment unchanged to other electronics blocks.
When tracing a sensor circuit, check the signal, supply and common reference together. An illuminated indicator on an inductive sensor does not establish that the correct signal reaches the input terminal. Check the sensor output type against the input circuit’s sink/source wiring requirements.
Protective earth and the M/0 V circuit reference serve different purposes. Review grounding against the cabinet drawings. Links found on another terminal block should not be copied without establishing the function of each connection.
Supply and load checks
When investigating a fault, do more than measure the output of the power supply. Check voltage between the relevant circuit supply and common terminals under operating load. A loose connection or cable voltage drop can cause intermittent operation even when the electronics block is healthy.
For output circuits, review the connected load’s operating current, starting behaviour and protection arrangements. The presence of a relay output does not make every load voltage acceptable. Apply the switching limits of the actual electronics block.
Field cables and connectors belong in the same investigation. A symptom that changes when a cable is moved calls for inspection of the connection, including loose clamping points and deteriorated contacts.
PROFIBUS and station settings
The base includes a PROFIBUS-DP connection, address selectors, coding slide and STOP/RUN switch.
If the station does not communicate, compare the PROFIBUS connection and address settings with the hardware configuration in the PLC project. Recording selector positions and cable labels before replacement reduces uncertainty when recommissioning the existing automation system.
STOP must not be treated as isolation of every field circuit. Disconnect the relevant supplies and verify the absence of voltage at the work location before touching the terminals.
Conductor sizes and fuse
Supply and signal connections permit up to 1.5 mm² with ferrules or 0.14–2.5 mm² without ferrules.
The specified fuse is TR5-T 1.6 A, order number 6ES7193-0DA00-0XA0. Its current rating must not be used as the output capacity of each channel.
Inspect more than screw tightness. Look for crushed ferrules, exposed strands, discoloured contact points and cracked insulation. Repeated fuse operation requires investigation of a short circuit or wiring fault rather than fitting a higher current fuse.
Maintenance and replacement selection
Include the complete 6ES7 193-0CA10-0XA0 reference and the electronics block label in a replacement enquiry. Clear photographs of the terminals and mating contact area are useful alongside the front view.
A single failed channel, a group of inactive loads and a complete loss of station communication are different symptoms. Record which condition occurs and what measurements have been taken. This helps distinguish a connection problem from an electronics fault and avoids replacing parts solely on suspicion.
Editor’s note: Start with the exact electronics block reference. In particular, treating “16DO” and “16DO/2A” as interchangeable names can lead to the wrong base selection. A readable label photograph and the existing wiring diagram provide a stronger basis for replacement than channel count alone.
Technical manual and wiring diagrams
Reference: Siemens ET 200B Distributed I/O Station, EWA 4NEB 812 6089-02c; section 7.2.1 and the relevant electronics block subsection under 7.3. Visit our Siemens ET 200 manuals and PDF documentation page to explore the documents.
Related topics and product categories
For an introduction to the family, visit About Siemens ET 200. You can also browse connection modules, additional modules, power supply modules and power distribution modules. Check compatibility using each part’s complete model reference.
Explore Siemens products: Siemens | Siemens S7 PLC | SIMATIC S7 | ET 200 products