6ES7 157-0AA80-0XA0

Siemens 6ES7 157-0AA80-0XA0 – IM 157 PROFIBUS DP/PA Link Interface Module

6ES7 157-0AA80-0XA0 is an IM 157 interface module from the Siemens SIMATIC range. It forms part of a DP/PA Link, allowing PROFIBUS PA field instruments to communicate with the higher-level control system. In an existing process installation, it is an important component in the communication path between field devices and the PLC.

The article number is also written as 6ES7157-0AA80-0XA0. When identifying a replacement, the IM 157 family name alone is insufficient. The 0AA80 version and the hardware information on the module label should be checked together.

What does it do within a DP/PA Link?

A DP/PA Link combines an IM 157 with suitable DP/PA couplers. The link operates as a slave on the PROFIBUS DP side and as a master on the PA side, providing a communication path between process instruments and the SIMATIC S7 control system.

The components have separate responsibilities: the IM 157 provides the communication interface, while the DP/PA coupler provides the physical PA segment connection and its power supply. Purchasing an IM 157 therefore does not provide a complete DP/PA Link station. The installed couplers, bus modules and mounting arrangement also need to be considered.

Main technical characteristics and capacity

Manufacturer: Siemens
Product family: SIMATIC IM 157
Article number: 6ES7 157-0AA80-0XA0
Function: DP/PA Link interface module
Specified temperature range: −25 to +60 °C
DP communication range: 9.6 kbit/s to 12 Mbit/s, subject to master and system restrictions.
Classic DP/PA Link arrangement: Up to 5 DP/PA couplers and a total of 31 PA field devices per link.

The 31-device figure does not mean that each coupler can support another 31 devices. Actual capacity also depends on coupler output current, field-device consumption and the amount of I/O data being transferred. When planning an automation installation, available addresses are only one part of the calculation.

PA instruments and analog input modules

A pressure or temperature transmitter equipped with PROFIBUS PA can participate in this arrangement through an appropriate PA segment. A conventional transmitter with a 4–20 mA output cannot be connected directly to the IM 157. That application requires a suitable analog input module or an appropriate conversion device. Identifying the instrument's output and communication interface is therefore an essential part of selecting the hardware.

Redundancy and bus module compatibility

The 0AA80 version supports redundant operation in an appropriate S7-400H and DP/PA Link configuration. This arrangement uses two IM 157 modules and the correct active bus hardware. Siemens documentation for this generation identifies the 6ES7 195-7HE80-0XA0 IM 157 bus module and the 6ES7 195-7HF80-0XA0 DP/PA coupler bus module.

A similar-looking bus module from a later generation should not be assumed to fit the application. In particular, 6ES7 195-7HD80-0XA0 must not be treated as a direct spare for the older 7HE80 bus module. When researching connection modules, use the complete article number and the manufacturer's approved combination.

Are 0AA80, 0AA81 and 0AA82 interchangeable?

These article numbers identify different IM 157 versions. Siemens documents the use of 0AA82 as a replacement for earlier versions in certain DP/PA Link arrangements. This does not establish unrestricted compatibility for every mixed configuration. The redundant pair, bus base and project configuration must be assessed together.

Features described for later versions, including firmware updates over the bus, expanded diagnostics and configuration changes during operation, should not automatically be attributed to the 0AA80. When comparing PROFIBUS and PROFINET interfaces, the hardware generation matters as much as the family name.

Commissioning and fault investigation

A useful starting point is the existing STEP 7 project, the IM 157 label, the coupler article numbers and the configured PROFIBUS addresses. Then check the power supply, bus termination, cable shielding and grounding arrangement. A loose or damaged connector can cause communication interruptions that resemble an interface module fault.

An important master-side restriction: Siemens specifies a 1.5 Mbaud limit for the CP 443-5 Extended 6GK7443-5DX03 in S7-400H/FH systems when used with this IM 157 generation, unless the relevant remedy has been applied. The module's 12 Mbit/s upper figure should therefore not be interpreted as an available operating speed in every existing installation.

Manuals and replacement selection

Start your documentation search from our Siemens ET200 manuals and PDF documentation page. For this product, check that the document covers IM 157 / DP/PA Link equipment and specifically addresses 6ES7 157-0AA80-0XA0. Technical specifications from a later-generation manual should not be transferred to this version without verification.

Editor's note: When identifying a spare for an installed station, prepare a photograph of the IM 157 label, the article number of its bus module and a list of the adjacent couplers. Together, these details make it much easier to distinguish similar components and assess the correct replacement. This page provides technical product information; availability and the scope of supply are assessed separately.

Related product groups and information

For other equipment in the control cabinet, browse our categories for ET200 power supply modules, power distribution modules, terminal blocks, additional modules and other network interfaces. These links introduce related product groups; they are not a list of accessories approved for direct use with the IM 157.

Explore: Siemens ET200 | About ET200 | Siemens S7 PLC products