6ES7 134-7SD00-0AB0
Siemens 6ES7 134-7SD00-0AB0 – ET 200iSP 4 AI TC Thermocouple Input Module
Siemens 6ES7 134-7SD00-0AB0 is a four-channel analog thermocouple input module for SIMATIC ET 200iSP stations. Its product designation is 4 AI TC. It measures low-level thermoelectric signals and makes temperature information available to the control system. Within the Siemens ET 200 family, this model serves thermocouple measurement applications in process automation stations designed for the applicable hazardous-area requirements.
Four Channels for Temperature and Millivolt Measurement
The module supports thermocouple measurement and a voltage range of −80 mV to +80 mV. Resolution is 15 bits plus sign, giving 16 bits in total. Siemens operating instructions list thermocouple types B, E, J, K, L, N, R, S, T and U. Sensor characteristic linearization follows the selected measurement configuration.
The physical thermocouple type, project setting and extension cable must match. A Type K sensor configured as Type J can produce an incorrect temperature even with intact wiring. Pt100 and 4–20 mA measurements require modules suited to those input signals; related options can be reviewed under ET 200 special input applications.
Cold-Junction Compensation and the TC Sensor Module
Accurate thermocouple measurement also requires the temperature of the reference connection. The 6ES7 134-7SD00-0AB0 performs internal cold-junction compensation through a TC sensor module mounted on the terminal module. Siemens specifies that this sensor module can be connected only to terminal modules with screw terminals. This requirement matters when selecting the terminal arrangement.
External compensation can use a reference temperature acquired by a suitable analog module in the same ET 200iSP station. Before replacing hardware in an existing cabinet, check whether the project uses internal or external compensation. The installed terminal module and the presence of the TC sensor belong in that assessment.
Conversion Time and Measurement Smoothing
Basic conversion time per channel is 80 ms with 50 Hz interference suppression or 66 ms with 60 Hz suppression. At 50 Hz, the basic four-channel cycle is 320 ms. Additional timing effects from wire-break monitoring and filtering must also be considered. Four levels of measured-value smoothing are available.
Stronger smoothing can reduce visible fluctuations while delaying the response to a temperature change. Select the setting according to the process response requirement. Processing in the PLC, together with HMI and SCADA update intervals, also affects the overall monitoring response.
Diagnostics, Limit Values and Signal Wiring
The module supports configurable diagnostic and limit-value alarms. A red SF LED indicates a group fault. During commissioning, review measurement type, compensation method, channel parameters and alarm limits together. Including the measurement point’s name in the alarm description helps maintenance personnel locate the associated field sensor.
Siemens specifies a maximum shielded cable length of 50 metres. The capacitance and inductance limits of the intrinsically safe circuit must also be satisfied. Suitable extension cable, correct polarity and the grounding arrangement influence low-level thermocouple measurements. Plan sensor cable routes alongside the cabinet’s power circuit layout.
ET 200iSP and Hazardous-Area Conditions
The module is used within ET 200iSP for intrinsically safe field circuits. Siemens product information requires a suitable Ex e enclosure for Zone 1 installation. Sensors of suitable equipment categories in Zones 0, 1, 2 and Zones 20, 21, 22 may connect to its inputs when the certified connection conditions are met. Assess the sensor, cable and module’s electrical intrinsic-safety limits together.
Hazardous-area suitability must be checked against the installed hardware’s label and certificate. Temperature monitoring tasks requiring functional safety also need a separate assessment of the safety module, controller and application requirements.
Terminal Arrangement, Supply and Dimensions
The electronic module plugs into an ET 200iSP TM-IM/EM or TM-EM/EM terminal module. Select the station’s connection components, power supply module and communication interface specifically for the ET 200iSP system.
Maximum current consumption from the power bus is 30 mA, with typical power loss of 0.4 W. Dimensions are 30 × 129 × 136.5 mm. Cabinet planning should also allow for the terminal arrangement and cable connections.
Editor's Advice
When selecting a spare, record the terminal type, TC sensor module and configured compensation method alongside the front label. If several channels show temperature offsets together, investigate their shared reference temperature and local terminal heating. This helps distinguish individual sensor faults from a compensation problem.
Technical Documents and Related Topics
Visit our Siemens ET 200 manuals and PDF documents section for connection, parameter and installation information. Review the ET 200iSP system manual together with the 4 AI TC product information and the Ex certificate applicable to the installed hardware.
Related topics: Siemens ET 200 system overview · ET 200 functional modules · ET 200 additional modules