6ES5 760-0HA11

Siemens 6ES5 760-0HA11 — IM 314H/R Terminating Plug

Siemens 6ES5 760-0HA11 is a terminating plug for IM 314H/R connections in SIMATIC S5 systems. The manufacturer’s diagram shows a 50-contact connection. It belongs to the S5 interface hardware and is specified at the end of the IM 314R link in S5-115H installations.

In an S5-115H switched expansion arrangement, IM 314R — 6ES5 314-3UR11 works with the central-controller-side IM 304 — 6ES5 304-3UB11. For relevant configurations using equipment such as the ER 701-3LH11 expansion rack, 0HA11 must terminate the correct endpoint.

Position on the IM 314R link

The S5-115H installation instructions specify 6ES5 760-0HA11 on the lower front connector of the last IM 314R. Trace the connecting cable and identify the final station first. The 6ES5 760-1AA11 specified for a standard IM 314 link is a different selection from 0HA11 for H/R applications.

Central-controller use without IM 306

The fixed-slot-addressing section of the same S5-115H manual also requires 6ES5 760-0HA11 in the IM slot when a central controller is operated without an IM 306. Assess this separately from termination at the front connector of the final IM 314R.

When inspecting a central installation, record whether it uses a CR 700-0LB, CR 700-2 or CR 700-3 rack, together with the equipment in its IM position. A general “S5 rack” description does not establish the correct location for the plug.

Connection and compatibility checks

The plug provides electrical termination for the connection. It does not perform the function of a processor or interface card installed in the mounting rack, and it is not addressed as a separate I/O module in the PLC program. Match the part to the interface and system arrangement.

The manufacturer’s pin diagram shows multiple signal lines and internal connections. Mechanical fit or a single resistance reading therefore cannot establish suitability. Match the order number, contact arrangement and application diagram; do not substitute an improvised resistor or jumper.

Troubleshooting and used-part assessment

If an expansion unit cannot be accessed, check its power supply, cable seating, interface indicators and termination in sequence. In PLC troubleshooting, an incorrect or missing terminator is one possible cause to investigate, rather than proof of a particular fault.

If several digital input and digital output groups in the same rack become inaccessible together, inspect their common connection path before replacing individual cards. Support the inspection with supply measurements and system diagnostic information.

For long cable routes, also examine grounding, equipotential bonding, shield connections and possible sources of electromagnetic interference. A fitted terminator does not establish that the rest of the cable installation is sound.

Editor’s note

It is easy to overlook a small plug like this. On an older Siemens S5 system, a missing termination can send you on a much longer search than expected. Check its identity and position before deciding that several otherwise serviceable cards need replacing.

Before removal, photograph the plug in its installed position, with the interface order number visible. Keep the lower IM 314R connection distinct from the central rack’s IM slot. A clear photograph makes reassembly much easier.

Take a moment to check the full number when a similar-looking spare turns up. 0HA11 and 1AA11 are different selections. Housing colour and appearance are poor substitutes for confirming the interface and its wiring instructions.

Inspect a used part’s contacts closely. Ask about bent pins, corrosion, loose retention or evidence of internal modifications. A clean housing alone cannot establish that the internal connections are correct.

Carry out the inspection with the equipment de-energized and label removed parts as you go. For a replacement enquiry, provide the full order number, quantity, label photograph and intended IM module. Those few details can prevent a disproportionate amount of confusion.

OtomasyonAVM resources and PDFs

+ S5 interface modules and S5 mounting racks: review the hardware associated with the plug.

+ OtomasyonAVM S5 PDF archive: related system documentation.

+ S5-115H system manual — English PDF: p. 3-25, lower front connector of the last IM 314R; p. 5-2, central controller without IM 306.

Related topics

+ 6ES5 314-3UR11 — IM 314R expansion interface

+ 6ES5 304-3UB11 — IM 304 central-side interface

+ 6ES5 760-1AA11 — different terminator for standard IM 314

+ 6ES5 701-3LH11 — S5-115H expansion rack

Browse SIMATIC S5

+ S5 interface modules

+ S5 cables and connectors

+ S5 mounting racks

+ SIMATIC S5 overview

+ Used Siemens equipment

Siemens and external references

+ Siemens S5-115H Manual — English; pp. 3-25 and 5-2, the two termination applications

+ Siemens U Periphery, IM 304/IM 314 instructions — English; p. 9, IM 314 versus IM 314H/R termination

+ Siemens 6ES5 760-0HA11 pin assignment — English document, p. 24

+ Siemens ST 50, 1998 — English; p. 3/93, 760-0HA11 ordering entry for IM 314R; archived copy