6ES5 455-7LA11

Siemens 6ES5 455-7LA11 – 16-Channel AC Digital Output Module

6ES5 455-7LA11 is a digital output module providing 16 electronic AC outputs in the Siemens SIMATIC S5 family. Used in the SIMATIC S5 S5-115U system, it arranges its outputs in eight optically isolated groups of two. Nominal load voltage is 48/115 V AC, with a total current limit of 2 A per two-output group.

Supply and load selection

The permissible load supply range is 40–140 V AC at 47–63 Hz. This board should not be selected for 24 V DC or 230 V AC loads. For contactor and control relay coils, check voltage, continuous current and inrush current together.

Assess the external load circuit separately from the power taken from the system bus. During power supply and PLC supply checks, a running PLC does not establish that the output group has its required load voltage.

Group current and fuse protection

The combined current of two simultaneously active loads in one group must not exceed 2 A. The stated output operating range is 40 mA–2 A; the upper value remains subject to the group total. Include this shared limit when selecting fuses and calculating load current. Outputs cannot be connected in parallel to increase current.

Each group is protected by a fuse; a red LED for each group indicates a defective fuse. Use the manufacturer's instructions for the actual board version when replacing a fuse. Investigate the load fault before replacement and do not increase the fuse rating to bypass the problem.

Leakage current and switching

The specified maximum off-state leakage is 1 mA or 3 mA, depending on the supply voltage. This matters with low-power or high-impedance loads. Maximum switching frequency is 10 Hz.

Observe the PLC program command, CPU output bit and actual load behaviour together. During troubleshooting, an unloaded voltage measurement alone does not establish a healthy output. Check conduction under load and behaviour in the off state as well.

Front connector and cabinet wiring

The ST 50 catalogue specifies a 24-pin front connector for this module; the screw-terminal option is 6ES5 490-7LB11. Select S5 cables and connection parts and connectors using the full order number and wiring diagram.

Check the S5 rack, rack/slot suitability, existing wiring and S5 system architecture together. Review AC load cable routing alongside electromagnetic interference and earthing arrangements.

The manual specifies a maximum of 175 mA from the 5 V system bus, typical power dissipation of 16 W and an approximate weight of 1.1 kg. Include this heat contribution when assessing cabinet ventilation.

Related order numbers and used-module checks

6ES5 456-7LA11 and 6ES5 456-7LB11 are AC output models with different voltage/current arrangements. 6ES5 454-7LA12 has DC outputs. Similar order numbers do not establish direct interchangeability.

On used Siemens equipment, inspect the label, front connection, fuse holders and signs of overheating. Do not stop after testing a few channels: test all 16 outputs with suitable loads within the group current limits.

Editor’s note

Keep one figure firmly in mind: 2 A is shared by the two outputs in a group. Two loads drawing 1.2 A each make 2.4 A. Write down and total the loads first; it saves time searching for the reason a fuse keeps blowing.

Take a moment to read the 48/115 V AC marking. Put the old and replacement boards side by side and compare the complete order numbers. Boards that look alike may have different load requirements.

If your meter shows voltage with the output off, pause before blaming the board. Remember the leakage current and 40 mA minimum load. Assessing the measurement with an appropriate load can save an unnecessary board replacement.

If a red group LED is lit, start with the fuse, wiring and loads in that group. A larger fuse does not cure the fault. Find the cause so that a sound replacement board does not meet the same problem.

Photograph and label the wiring before removing the connector. A few minutes spent recording it makes reassembly easier. Isolate the module and every external load supply before removal or insertion. Finish by checking every output so the job is properly settled.

OtomasyonAVM resources and PDFs

Start with About Siemens S5 PLC, S5 digital output modules and the OtomasyonAVM Siemens S5 PDF archive. The exact technical table is covered in the English Siemens manual and ST 50 catalogue below.

Related topics

+ 6ES5 456-7LA11 · 6ES5 456-7LB11 · 6ES5 454-7LA12: comparing different output models.

+ 6ES5 490-7LB11 front connector · Fuse rating and load current · PLC troubleshooting.

Browse SIMATIC S5

S5 digital output modules · S5 cables and connectors · S5 racks · Used Siemens equipment

Siemens and external references

+ Siemens S5-115U CPU 945 Manual – English: printed 15-32 / PDF 617, specifications and connection drawing for 6ES5 455-7LA11.

+ Siemens ST 50, 1998 – English catalogue mirror: printed 3/37–3/38 / PDF 123–124, output specifications and front-connector ordering data.