6ES5 420-4UA11

Siemens 6ES5 420-4UA11 – 32-Channel 24 V DC Digital Input Module

Siemens 6ES5 420-4UA11 is a 32-channel, 24 V DC, non-isolated digital input module for SIMATIC S5 U-range peripheral systems, including S5-135U applications. Within the S5 digital input module range, it provides four input bytes, 8.5 mA rated input current, a typical 3 ms delay and a separate F+ enable input.

The module reads signals from inductive sensors, photoelectric sensors and limit switches. Each of its thirty-two inputs reports an ON/OFF state and has a green front-panel status LED. The start address is set on the module’s own address switch; it is not derived solely from the slot number.

Input levels, current and response time

The rated input voltage is 24 V DC. Logic 1 is specified at 13–33 V and logic 0 at −33 to +5 V; the region between +5 V and +13 V is undefined. For the positive switching arrangement, consider the difference between PNP and NPN sensors and connect the field power supply L− reference according to the manual’s grounding arrangement. Non-floating means that galvanic isolation is absent.

Rated input current is 8.5 mA and typical input resistance is 2.8 kΩ. The delay is typically 3 ms, with a specified range of 1.4–5 ms; the maximum input frequency is 100 Hz. The PLC scan also affects the overall response. This is a digital input module, rather than an analog measuring input or a high-speed encoder counter.

Siemens specifies a 100% diversity factor, allowing all inputs to be ON simultaneously. Cable limits are 600 m unshielded and 1000 m shielded. The digital section draws typically 80 mA at 5 V from the system bus. The specified supply range for two-wire BERO proximity switches is 22–33 V; include the sensor’s voltage drop when checking the interface.

Front connector and input terminal assignment

The module measures 20 × 255 × 195 mm and weighs approximately 0.4 kg. Check front-connector width and cooling conditions when reviewing the S5 rack and carrier. For fan-cooled operation, the manual lists the 20 mm wide, 42-pole crimp 6ES5 497-4UA12 connector. Different connector widths are provided for fanless arrangements and screw-terminal connections.

Front-connector pin 1 is the F+ enable input. The first input byte uses pins 4–11, the second 13–20, the third 25–32 and the fourth 34–41. Bits progress from 0 to 7 within each group. With start byte 80, for example, pin 4 is I80.0, pin 11 is I80.7 and pin 13 is I81.0. Do not use the intervening unassigned pins as distribution terminals.

F+ enable input and the −4UA12 distinction

F+ is a rated 24 V DC enable input, with a logic-1 range of 13–33 V, rated current of 5 mA and maximum cable length of 200 m. Loss of the enable supply can remove the module’s bus acknowledgement and produce a QVZ/acknowledgement timeout. The enable-mode jumper associated with 6ES5 420-4UA12 applies to the −4UA12 version; do not treat that setting as a −4UA11 feature.

Address switch, four bytes and STEP 5 example

The start address is the sum of the binary weights set to ON on the module’s address switch. In the Siemens example, 80 = 64 + 16 = 50h selects input bytes 80, 81, 82 and 83; the next free input address is 84. When checking the Siemens S5 PLC addressing arrangement, ensure that these four bytes do not overlap another input module. STEP 5 may display inputs with I or E, depending on the mnemonic language.

Revision selection and SINUMERIK applications

When considering later versions such as 6ES5 420-4UA13 or 6ES5 420-4UA14, compare the enable circuit, connections and technical revision together. Matching thirty-two inputs and 24 V does not establish a direct replacement. The 6ES5 430-4UA11 is a different, galvanically isolated module; its isolation specification must not be attributed to the 420-4UA11.

Siemens lists the exact 6ES5 420-4UA11 in the SINUMERIK 810G GA3/820G GA3 Mini EU documentation, paired with 6FC3 988-4DB. The same list includes the 6ES5 441-4UA11 and 6ES5 454-4UA11 output modules. This documents a specific CNC peripheral arrangement, rather than unconditional compatibility with every SINUMERIK chassis.

The 6ES5 420-3BA11 uses compact K construction, while the 6ES5 420-5AA11 uses rugged A-version construction. Avoid ordering from the description “420 input card” alone. When sourcing a used digital input module, check the complete order number, address switch, front connector, F+ operation and individual results for all thirty-two channels.

Editor’s note

A lit LED is only the first check. Confirm that the matching input changes at the correct STEP 5 address. If the field signal is present but the CPU cannot read the card, inspect F+ and the address setting early in the diagnosis.

Remember pin 1 on the front connector. It is the F+ enable input, not an ordinary process input. If every channel appears faulty after replacement, measure the enable connection before condemning all thirty-two inputs.

Photograph the address switch before removal. On this module, the address switch remains decisive when the slot changes. Record the old setting and compare all four input bytes with the program.

Keep −4UA11 and −4UA12 separate in your checks. Read which version the enable jumper belongs to. Diagnose why the existing circuit grants or removes enable instead of experimenting with arbitrary jumper changes.

Test the inputs in four groups. Work through pins 4–11, 13–20, 25–32 and 34–41 in order. Measure the common reference on this non-isolated module, and establish bench-test conditions that prevent machine movement.

OtomasyonAVM resources and PDFs

+ Siemens S5 PLC main page

+ S5 digital input modules

+ S5 PDF files — shared manual archive

Related topics

+ 420-4UA12 and enable-circuit revision differences

+ 497-4UA12 front connector

+ PNP and NPN sensor comparison

Browse SIMATIC S5

+ S5 digital input modules

+ SIMATIC S5

+ Siemens second-hand main page

+ Used digital input modules

Siemens and external references

+ Siemens U Periphery — English; 420-4UA11/12 specifications and wiring, section 5.1, pages 33–34

+ Siemens SINUMERIK 810G GA3/820G GA3 Installation Lists — English, 05.92; Mini EU list on 1-5