Delta DVP16ES200R

Delta DVP16ES200R – Compact PLC with 8 inputs and 8 relay outputs

The Delta DVP16ES200R is a compact Delta DVP-ES2 PLC CPU with a 100–240 V AC supply, eight 24 V DC digital inputs and eight relay outputs. Typical applications include small conveyors, filling stations and auxiliary machine circuits. The PLC reads pushbuttons and sensors and switches suitable valves, indicators or contactor coils.

Inputs, relay outputs and panel wiring

The digital inputs are addressed X0–X7. Match the S/S input common to the PNP or NPN sensor circuit shown in the Delta wiring diagram. Sink/source wiring determines the direction of signal current. An inductive sensor can detect metal parts, a photoelectric sensor can detect passing products and a limit switch can report end-of-travel. Match the field device’s NO/NC contact action to the condition in the PLC program.

The Y0–Y7 relay outputs share two common terminals C0 (Y0–Y3) and C1 (Y4–Y7). Delta’s 2 A per point and 5 A per common ratings apply to resistive loads. For contactors, solenoids and lamps, check load type, inrush current, suppression and fuse selection. Follow the panel’s protective grounding requirements and route signal wiring away from power cables.

The built-in I/O is digital. The difference between analog and digital inputs matters when adding a pressure transmitter or speed reference. For 0–10 V or 4–20 mA analog signals, use a compatible expansion module or consider a Delta DVP-EX2 CPU with built-in analog I/O.

Programming software and cable

Use Delta WPLSoft to open existing ladder diagram projects, read programs from the PLC and monitor logic online. Delta ISPSoft also supports DVP-ES2. When programming the PLC, select DVP-ES2 as the target and check instruction support against the installed CPU firmware. Delta’s programming manual lists 15,872 program steps for ES2.

For a USB-equipped PC, use the Delta UC-PRG020-12A USB-to-RS-232 cable and plug its mini-DIN end into COM1. For a PC with a physical RS-232 port, the Delta UC-MS020-01A serial cable is also suitable. Install the USB cable’s Windows driver and select the assigned COM number in WPLSoft. For ISPSoft, start an RS-232 driver on that COM port in COMMGR, then select the same connection in ISPSoft. See the Delta PLC programming cable guide.

RS-485 communication and model selection

COM2 and COM3 are RS-485 ports. To connect an operator panel or drive over Modbus RTU, match the station address, baud rate, parity and device roles. Check topology and termination for the Modbus RS-485 connection. The RS-232, RS-422 and RS-485 comparison and industrial communication guide cover the relationship between the physical interface and the protocol.

The DVP16ES200T has the same 8 inputs and 8 outputs, with NPN transistor outputs. For high-speed pulse commands to a servo or stepper drive, check the T model’s pulse outputs against the drive interface. If more inputs are needed, the DVP24ES200R offers 16 inputs and 8 relay outputs. The DVP32ES200R offers 16 inputs and 16 relay outputs.

Editor’s Note

Read the nameplate before buying used. Check the final R in the ordering code, the AC supply rating and the condition of the removable terminal blocks.

Back up the running machine first. Read and save the PLC program. Record the serial settings, station address and any retained data needed by the machine.

Start with the cable if communication fails. Check the Windows COM assignment, the mini-DIN socket pins and the port settings. Plan access if the HMI and service PC need the same port.

A relay can click even when its contact fails under load. Isolate power and inspect C0/C1 and the wiring. With machine loads disconnected, test each output using a suitable test load. See electrical measurement and test concepts.

Check the field wiring when an input appears faulty. Verify S/S and the sensor supply. Compare the input LED with the corresponding X address in the software.

Internal references and PDF files

Delta DVP PLC PDF files · DVP-ES2 installation and wiring guide (Turkish PDF)

Navigation · Delta Automation · DVP PLC series · DVP-ES2 series

External references

Delta DVP-ES2 installation sheet (multilingual PDF) · Delta DVP product catalogue · Delta DVP programming manual · Delta PLC/HMI cable selection guide (§1.1) · Delta ISPSoft user manual (§2.4.8)